Nell is once again running strong. Great, in fact!
The problem with the distributor? The rolled pin that holds the distributor gear to the shaft had started to back out, and needed to be replaced. Cost of replacement? 23₵, and less than an hour's work, including the drive time to the auto parts store!
To pull the distributor, I first put #1 cylinder on TDC. I wanted to be absolutely sure where the rotor should be when I put the distributor BACK. With the distributor cap off, I pulled #1 spark plug, disconnected the hot start ignition wire from the coil, and bumped the engine with a remote starter until the rotor lined up with the #1 mark.
Then I confirmed that #1 was at TDC with the timing marks (down there by the pointy thing)
After disconnecting the electrical connections and removing the hold down bolt, the distributor slipped right out. I could diagnose the problem right away by looking at the drive gear!
The rolled pin was sticking out, and had actually disengaged completely on one side. I could wobble the gear back and forth a little on the shaft. No doubt about it! This was the source of my timing problem. The end of the pin was cracked, and it fell to pieces when I used a drift to tap it out:
There are probably a few tiny bits of rolled pin in the engine oil pan or oil filter right now. I'm hoping they stay there! 23 cents at NAPA got me a new pin (I spent more on gas getting there)!
I juiced the new pin up with red loctite, tapped it in position, then peened the ends between a pair of center punches using a vise and a heavy hammer! This one isn't coming out on its own! Nell fired right up once I replaced the distributor. I let her warm up, then easily set the timing to 14° BTDC. She idled well, and pulled very strong during my short test drive. Nell is back, and she's having a blast!
What did I learn from this? Well, I got disenchanted with the Mallory distributor before I had a chance to pull it and confirm what was going on. I seemed to forget how good it has performed over the last 3000 miles. In my disenchantment, I purchased a (rather expensive) 1957 Mercury tach drive distributor from eBay. I had been debating getting one of these anyway, but I could have been more patient.
I must confess that I do this all the time. With each new upset or disappointment, I forget what has worked for me in the past. I forget how much God has blessed me. My longing and obsession kicks in, and I try to work my way out of the pain or disappointment. Patience is the last thing I want to experience!
Still, I find that God can redeem my mistakes. The guy selling the distributor is extremely friendly. He lives in New York and has a yard full of old Fords, with more than a few Y-blocks. We talked for half an hour or so, and I told him about Nell and this blog. He set the distributor up for me to make sure it worked properly, and even set me pictures of it running in one of his engines! Now that's service!
If you are new to this blog, please start with the oldest post... then click on "newer post" at the bottom of each post to read the whole story.
Friday, October 18, 2013
Sunday, September 29, 2013
Advance Setback...
The wife and I drove Nell to a meeting at church this evening. I knew something was wrong as I pulled out of the driveway. There just didn't seem to be much power! During the entire 5 miles to church, I kept thinking "something just isn't right!" It was bogging and lagging, and I couldn't go much over 50 on the freeway. The car ran great yesterday... what could be wrong now?
By the time we got to church, I could smell burning plastic. Nell was idling too low, and seemed ready to stall. I pulled into a parking lot and opened the hood... the tach cable casing had melted where it goes over the battery heat shield. This has never happened before... the heat shield was HOT... so were the exhaust manifolds... really hot!
Well, we went to the church meeting, figuring that Nell could probably get us home again. She did, but it wasn't a fun ride. The engine bogged terribly, and backfired under load if I gave it more than half-throttle. I was grateful to get home without incident, and back Nell into the garage to cool down.
I suspect that the advance mechanism on the mechanical advance Mallory Unilite distributor has somehow failed. It is a racing model with no vacuum advance, so it may not be advancing at all. All the symptoms point to this. I will check on repairing the distributor, but I may also be interested in replacing it with a '57 vintage Ford/Mercury tach drive distributor. Having a vacuum advance will make the engine run cooler at idle, and will improve fuel economy a little. Unfortunately, these distributors are rare and expensive... I've been looking for a good deal on one for almost two years!
I'll give the Mallory another chance... tomorrow I'll check the advance with a timing light. If so, I'll pull the rotor and see if there is anything obviously wrong with the advance mechanism, like a broken spring or something. If not, I may be going shopping.
Update 9/30: I checked the timing with a timing light, and it was all over the place. I pulled the cap and rotor off the distributor, and found that the backing plate (underneath the advance mechanism) could be moved back and forth about 10 degrees! This is not good, and indicates to me that something important has come loose inside the distributor. I'm hoping that the pin holding the drive gear to the shaft didn't shear off, because that means there is probably a little piece of metal rattling around inside the engine!
I plan on pulling the distributor weekend after next... this weekend I am taking a group of Boy Scouts on an Astronomy campout. In the mean time, I'm looking for a '57 tach drive distributor!
By the time we got to church, I could smell burning plastic. Nell was idling too low, and seemed ready to stall. I pulled into a parking lot and opened the hood... the tach cable casing had melted where it goes over the battery heat shield. This has never happened before... the heat shield was HOT... so were the exhaust manifolds... really hot!
Well, we went to the church meeting, figuring that Nell could probably get us home again. She did, but it wasn't a fun ride. The engine bogged terribly, and backfired under load if I gave it more than half-throttle. I was grateful to get home without incident, and back Nell into the garage to cool down.
I suspect that the advance mechanism on the mechanical advance Mallory Unilite distributor has somehow failed. It is a racing model with no vacuum advance, so it may not be advancing at all. All the symptoms point to this. I will check on repairing the distributor, but I may also be interested in replacing it with a '57 vintage Ford/Mercury tach drive distributor. Having a vacuum advance will make the engine run cooler at idle, and will improve fuel economy a little. Unfortunately, these distributors are rare and expensive... I've been looking for a good deal on one for almost two years!
I'll give the Mallory another chance... tomorrow I'll check the advance with a timing light. If so, I'll pull the rotor and see if there is anything obviously wrong with the advance mechanism, like a broken spring or something. If not, I may be going shopping.
Update 9/30: I checked the timing with a timing light, and it was all over the place. I pulled the cap and rotor off the distributor, and found that the backing plate (underneath the advance mechanism) could be moved back and forth about 10 degrees! This is not good, and indicates to me that something important has come loose inside the distributor. I'm hoping that the pin holding the drive gear to the shaft didn't shear off, because that means there is probably a little piece of metal rattling around inside the engine!
I plan on pulling the distributor weekend after next... this weekend I am taking a group of Boy Scouts on an Astronomy campout. In the mean time, I'm looking for a '57 tach drive distributor!
Saturday, September 21, 2013
Spare Tire
I've been going to cruise nights pretty regularly this summer. It has been a real joy to share Nell with family, friends and strangers. When my travel schedule allows, I try to drive her somewhere at least once a week. This is necessary to keep the gas fresh, the seals wet, and the car fully functional. Plus, I need a regular reminder of God's grace to me.
When I made my original decision about the wheels and tires on this car, I determined that I wanted a full size spare on a full size rim. Having a spare tire in the trunk provides insurance against the possibility of a certain kind of road hazard. Admittedly, the likelihood of this occurrence is pretty small, and the likelihood of it happening outside of cell phone and tow truck coverage is miniscule. Still, for almost a year I stowed the full size spare in the trunk. It wasn't a whitewall like the others, but it was exactly the same size... and it took up half the space in the trunk! It was also awkward to remove, since it was bulky and must weigh about 50 pounds.
At one of the first cruise nights this summer, I met a guy with a '57 bird who had a compact spare in the trunk. It was one of those collapsible jobs that they don't make any more... like the one that came in my '87 Firebird. This kind of spare needs a CO2 cartridge and/or electric pump to inflate it before it can be used. While it worked when I needed it on my Firebird, the cartridge/pump does take up more space and is one more thing that can go wrong.
When I started preparing for our trip up Highway 1, I kept thinking about all that room and weight in the trunk taken up by the spare. I started looking for a compact spare that might serve, and eventually got a Ford-style 4 1/2 x 16 aluminum rim spare with T145/80D16 tire on eBay for $50. This one was off a 98 or 99 Lincoln Town Car, but the same wheel/tire is used on Crown Vics and Mustangs. I didn't know if it would fit, but I lucked out:
I took on another minor improvement after returning from the convention. The driver side mirror had come loose in an awkward spot, and was rattling so badly that it was pretty much useless on the freeway. The problem is in the way the stainless mirror shell is riveted to the ball joint. I couldn't get to the back of the rivet without popping the glass out of the shell, and I really didn't know how to do that without breaking the glass. What to do? JB Weld to the rescue!
JB Weld is basically 2-part epoxy fortified with fine iron filings, and it's pretty tough stuff. Filling the gap between the stainless shell and the ball post with this stuff tightened up the joint and eliminated the rattle, for far less than the cost of a replacement mirror head. Since the passenger's side was a little loose too, I went ahead and did the same treatment on that side. This may be a temporary fix, but I'm happy with it for now. When I reassembled the mirrors, I applied a very thin layer of white grease on the joints to make them easier to adjust.
I'm getting ready for another life milestone in November. God continues to bless me. I will have to elaborate on that in my next post.
When I made my original decision about the wheels and tires on this car, I determined that I wanted a full size spare on a full size rim. Having a spare tire in the trunk provides insurance against the possibility of a certain kind of road hazard. Admittedly, the likelihood of this occurrence is pretty small, and the likelihood of it happening outside of cell phone and tow truck coverage is miniscule. Still, for almost a year I stowed the full size spare in the trunk. It wasn't a whitewall like the others, but it was exactly the same size... and it took up half the space in the trunk! It was also awkward to remove, since it was bulky and must weigh about 50 pounds.
At one of the first cruise nights this summer, I met a guy with a '57 bird who had a compact spare in the trunk. It was one of those collapsible jobs that they don't make any more... like the one that came in my '87 Firebird. This kind of spare needs a CO2 cartridge and/or electric pump to inflate it before it can be used. While it worked when I needed it on my Firebird, the cartridge/pump does take up more space and is one more thing that can go wrong.
When I started preparing for our trip up Highway 1, I kept thinking about all that room and weight in the trunk taken up by the spare. I started looking for a compact spare that might serve, and eventually got a Ford-style 4 1/2 x 16 aluminum rim spare with T145/80D16 tire on eBay for $50. This one was off a 98 or 99 Lincoln Town Car, but the same wheel/tire is used on Crown Vics and Mustangs. I didn't know if it would fit, but I lucked out:
![]() |
| Since the car has been lowered a little, I was concerned about ground clearance. The spare is 1 1/2" smaller diameter than the stock tires, but this isn't really a problem. |
I took on another minor improvement after returning from the convention. The driver side mirror had come loose in an awkward spot, and was rattling so badly that it was pretty much useless on the freeway. The problem is in the way the stainless mirror shell is riveted to the ball joint. I couldn't get to the back of the rivet without popping the glass out of the shell, and I really didn't know how to do that without breaking the glass. What to do? JB Weld to the rescue!
JB Weld is basically 2-part epoxy fortified with fine iron filings, and it's pretty tough stuff. Filling the gap between the stainless shell and the ball post with this stuff tightened up the joint and eliminated the rattle, for far less than the cost of a replacement mirror head. Since the passenger's side was a little loose too, I went ahead and did the same treatment on that side. This may be a temporary fix, but I'm happy with it for now. When I reassembled the mirrors, I applied a very thin layer of white grease on the joints to make them easier to adjust.
I'm getting ready for another life milestone in November. God continues to bless me. I will have to elaborate on that in my next post.
Sunday, August 11, 2013
CTCI Western Regionals
#1 Son and I had a great trip driving up Highway 1 from Dana Point to Santa Cruz, then across 17 to San Jose. I posted a slide show of the trip on YouTube:
I still enjoy watching this! The familiar sights, framed by the car windshield, give weight to the experience. The fog on the mountains, the surf on the rocks, the trees and the bridges, and the memory of the engine purring like a large cat... enjoying the experience with my son. This is the stuff of lifelong memory, the kind of thing I need to remember!
The Classic Thunderbird Club International meet was outstanding, with over 100 brightly-colored 55-6-7 'birds there. Over 40 were competing in touring class with "Nell", another 40 were display only, and over 25 were competing in the various Concours classes. Touring cars compete against each other (1st, 2nd, etc. in their own subclasses), but Concours cars only compete against themselves for points and awards (Bronze, Silver, Gold, etc.). There were even a few 'birds in the "underbirds" class, for cars that still need restoration.
I brought a new very cool wide angle lens for the camera, but unfortunately I left it in the bag the entire trip! Guess I had other things on my mind. Still, I took a lot of pictures with my standard zoom lens. Here are a few that start to capture some of the amazing colors at the show.
My son took several panorama shots on the Saturday t-bird tour to the Santa Cruz wharf. I've had fun stitching these together into some of the panoramas below.
I was completely surprised at the awards banquet last Saturday night, when Nell was awarded 3rd place in Hoods Up Touring, Class B! The other cars in Hoods Up Touring were absolutely stunning, and I didn't thing we would go home with anything but memories.
It was a fantastic trip, and I feel truly blessed. I was able to make new friends, and still have time to connect with friends and family in the bay area. My son and I really enjoyed the trip, and the time we spent together is priceless!
The Classic Thunderbird Club International meet was outstanding, with over 100 brightly-colored 55-6-7 'birds there. Over 40 were competing in touring class with "Nell", another 40 were display only, and over 25 were competing in the various Concours classes. Touring cars compete against each other (1st, 2nd, etc. in their own subclasses), but Concours cars only compete against themselves for points and awards (Bronze, Silver, Gold, etc.). There were even a few 'birds in the "underbirds" class, for cars that still need restoration.
I brought a new very cool wide angle lens for the camera, but unfortunately I left it in the bag the entire trip! Guess I had other things on my mind. Still, I took a lot of pictures with my standard zoom lens. Here are a few that start to capture some of the amazing colors at the show.
![]() |
| Nell shortly after arrival |
![]() |
| What a colorful flock! |
![]() |
| This car had the most amazing pearlescent paint. |
![]() |
| This car had been to each state capital in the lower 48 |
![]() |
| Nell getting prepped for judging. |
![]() |
| One of the rare supercharged "F-birds" |
![]() |
| A very sweet '57 "E" model, with twin 4 barrel carbs |
![]() |
| This is a stunning custom. Can you tell what is missing? |
![]() |
| The "underbird" class winner |
![]() |
| One of the original "bird nest" rumble seats |
![]() |
| Having fun with depth of field |
![]() |
| I couldn't pass up a good window-reflection shot! |
My son took several panorama shots on the Saturday t-bird tour to the Santa Cruz wharf. I've had fun stitching these together into some of the panoramas below.
I was completely surprised at the awards banquet last Saturday night, when Nell was awarded 3rd place in Hoods Up Touring, Class B! The other cars in Hoods Up Touring were absolutely stunning, and I didn't thing we would go home with anything but memories.
It was a fantastic trip, and I feel truly blessed. I was able to make new friends, and still have time to connect with friends and family in the bay area. My son and I really enjoyed the trip, and the time we spent together is priceless!
Sunday, July 28, 2013
Fully Ready
For the last four months or so, I've been looking forward to driving "Nell" to the Classic Thunderbird Club International regional convention with my #1 son. The convention is coming up this week, and my son and I are pretty pumped up about it! We will be driving Nell over 500 miles up the coast highway to get there, so it's important that she be in tip-top condition.
This summer I have taken Nell to several cruise nights, and she has been a reliable ride. I figured she was really ready for this long trip. Last Sunday, after taking my sweetheart out for a cup of coffee, I got out of the car and noticed drops of water appearing on the ground in front of the bumper! It looked like it was raining, but just in a very small patch immediately in front of the car, and the bumper was also wet. Kneeling down for a closer look, it became clear that the radiator had sprung a pinhole leak! Bummer! I guess she isn't ready after all. The radiator is pretty old, and probably should have been replaced a year ago... but I was too eager to get the car together. I thought I could get by with the old radiator.
Monday I was on the phone with T-bird parts houses trying desperately to find a radiator that I could get in a few days. On the third try, I found one in my state. When I came home from work on Tuesday, the new radiator had arrived! I got a heavy duty 4-row copper version, which should have a little extra cooling capacity.
I had Friday off, so bright and early I pulled the old radiator and started cleaning up the engine compartment. This is much easier to do with the radiator and fan removed.
I repainted the upper shroud gloss black. While paint was in the gun, I painted the aftermarket 6-blade fan as well. Then, on a lark, I decided to paint the tips of the fan yellow, like a WWII fighter plane! I'd seen pictures of another t-bird that had this done, and I thought it looked cool. The tips of warplane props were painted a bright color so that ground crews could see where the danger circle was when the engines were running. This seems like a good idea for a car engine, too. It also is my own way of paying homage to Uncle Toronado, the WWII P38 pilot that owned this car for 20 years.
Here are a few victory shots. Nell looks great, and is a genuine blast to drive. I'm really looking forward to the trip with my Son this week, and being around other t-birders for a few days!
-----
At my recovery meeting last week, the lesson was on Step 6... "being fully ready for God to remove all our defects of character". It's easy to think I am ready, and another thing to be fully ready. God has a remarkable way of reminding me of my lack of readiness. A lingering stare that could turn to lust, a lingering attitude or entitlement... these are like pinhole leaks in my radiator. Am I fully ready to let God fix me, to replace a part of me. Do I cringe at the cost of the repair, or do I move out in faith?
I had to let go of something this week that was holding me back from being fully ready. It may not be the only thing, but I'm just a little closer to being the man I want to be. The man I think God wants me to be.
This summer I have taken Nell to several cruise nights, and she has been a reliable ride. I figured she was really ready for this long trip. Last Sunday, after taking my sweetheart out for a cup of coffee, I got out of the car and noticed drops of water appearing on the ground in front of the bumper! It looked like it was raining, but just in a very small patch immediately in front of the car, and the bumper was also wet. Kneeling down for a closer look, it became clear that the radiator had sprung a pinhole leak! Bummer! I guess she isn't ready after all. The radiator is pretty old, and probably should have been replaced a year ago... but I was too eager to get the car together. I thought I could get by with the old radiator.
Monday I was on the phone with T-bird parts houses trying desperately to find a radiator that I could get in a few days. On the third try, I found one in my state. When I came home from work on Tuesday, the new radiator had arrived! I got a heavy duty 4-row copper version, which should have a little extra cooling capacity.
I had Friday off, so bright and early I pulled the old radiator and started cleaning up the engine compartment. This is much easier to do with the radiator and fan removed.
![]() |
| The before picture, after I drained the radiator. |
![]() |
| Taking the shrouds off is pretty easy. The rust stains on the radiator came from an ill-fitting cap that I used when I first assembled the car last year. |
![]() |
| The upper shroud showed some rust after I pulled off the old rubber strip. I repainted the shroud, and installed new rubber. |
![]() |
| The new radiator is just a little thicker, with an additional row of tubes. |
![]() |
| The engine compartment. detailed and reassembled. |
-----
At my recovery meeting last week, the lesson was on Step 6... "being fully ready for God to remove all our defects of character". It's easy to think I am ready, and another thing to be fully ready. God has a remarkable way of reminding me of my lack of readiness. A lingering stare that could turn to lust, a lingering attitude or entitlement... these are like pinhole leaks in my radiator. Am I fully ready to let God fix me, to replace a part of me. Do I cringe at the cost of the repair, or do I move out in faith?
I had to let go of something this week that was holding me back from being fully ready. It may not be the only thing, but I'm just a little closer to being the man I want to be. The man I think God wants me to be.
Tuesday, July 23, 2013
Return to Skygazing?
![]() |
| My telescope under the milky way... very inviting! The streak in the lower right is a meteor. Note the small guide scope mounted above the main tube. |
Dad didn't leave my siblings and me a large inheritance, but he did leave us something. I was able to buy my dear wife a beautiful and comfortable new crossover SUV, and my sister was able to buy herself a premium used convertible hardtop. Somehow buying cars with "Dad's money" seems appropriate, especially ones that we will enjoy. He did like cars.
There was enough left over that I started thinking about getting myself something special from Dad. I thought this seemed selfish at first, since Dad paid for the paint on the t-bird... but there are other things about Dad that I'd like to honor and remember.
I remember when Dad went "half-sies" with me to buy my first telescope in Jr. High. I had to save my allowance for several months, then we went to Fedco and picked up a Tasco 4 1/2" reflector on an equatorial mount. I thought it was glorious, and it opened up a whole new world for me. Dad remembered some of his Boy Scout astronomy, which wasn't very helpful. I pretty much figured out the telescope by myself.
We would haul the telescope up to the roof of the house and set it up to look at the moon and planets. We took it to the mountains, and looked at the stars. I didn't know the sky very well, and I didn't have good star charts, but I had fun. I think Dad enjoyed it too, or at least he enjoyed my enthusiasm.
I've since moved on through a series of much better telescopes, and I know the sky reasonably well. I have tried my hand at astrophotography, first with film and then with DSLRs. Dad never "caught the bug" for astrophotography, but he seemed to enjoy my efforts.
In mid-July a local telescope store held an astronomy expo in their parking lot, and put most of their inventory on sale. On a lark, I decided to "just see what they had", but deep down I had a pretty good idea of what I wanted. I came home with a new mount, autoguider, and guidescope... and significantly less money in the inheritance fund!
Normally, I really dislike spending money. Dad clearly didn't like spending it either. Still, I feel good about this... I feel like the stars are calling me back. I really did get a good deal on this equipment, and I expect it to serve me well for the rest of my life.
There is something about looking at the stars that calms my soul. It gives me perspective. It fills me with awe, and makes me feel closer to God.
Photography is about capturing images that touch our hearts. It seems logical and right for me to extend that practice to the night sky, which has grown to mean so much to me over the years. I think that's why I invest myself in this most exacting, most complex of photographic pursuits. It lets me share something that has become quite dear to me. I think Dad would approve.
Sunday, July 21, 2013
Automotive Ambassador
The evening after my last post (8 July), my wife and I drove "Nell" to church. There I gave a presentation about Christian Recovery to a group of Stephen Ministers. My wife and I have been Stephen Ministers for over a decade. It took 6 months of training before we were each commissioned, and we served actively as caregivers for 2 years. We have each had a variety of care assignments, both formal and informal, and we have continued to be active in training new groups of Stephen Ministers. Needless to say, we are both committed to active Christian one-on-one care giving.
It was a blessing to give my testimony and discuss the reality of addiction with a group of genuinely caring, supportive individuals. After telling my story, much of which I have related in this blog, I was able to clearly describe the importance of walking alongside someone who is working through the first three steps of recovery. I was able to talk about recovery in terms of faith: Redemption, Transformation, and Sanctification. I was able to explain why, at least for me, recovery is a life-long process that requires a daily statement of intention. I was able to explain why my relationship with God is a key part of being able to make this daily commitment.
I was also able to talk about car restoration as an analog to recovery, and to describe the particular importance I placed on the old hunk of blue painted metal and chrome that was sitting just outside the chapel where I was speaking. In the midst of difficult decisions or disappointments, sometimes I just needed someone to calmly listen, to help me explore and understand my own thinking, and to facilitate my own action, change, or acceptance.
Don't get me wrong... there are times when addiction is brutal, and self-exploration isn't even possible. That's when boundaries are important, and invasive treatment may be required. But after sobriety comes the difficult decision... who do I want to be? Who do I want to trust? That's the pivotal point where a little encouragement by a non-anxious presence can do the most good. That's when the real commitment to recovery begins.
Stephen Ministry is not a substitute for formal 12-step programs. A Stephen Minister is not a "Sponsor", but just someone to come alongside to talk and pray. I need my recovery meetings and my 12-step. But I also need my broader community of faith, and the variety of one-on-one relationships God puts in my life.
My #1 Son and I are planning on driving Nell to a CTCI regional meet in a few weeks. It will be a long trip, but I'm really looking forward to it. I thought the car was ready, but this morning I noticed a pinhole leak in the radiator after I drove my wife to get coffee! Bummer. I'm hoping that I can get this repaired next weekend.
I also got a new camera, so I can resume documenting Nell's progress and experiences in this blog. Hopefully next week I can post a story about installing the new radiator.
Subscribe to:
Posts (Atom)
































